Watlow Mineral Insulated Band Heaters

Sords Electric Sells Barrel and Band Heaters from Watlow

Mineral Insulated (MI) Band/Barrel Heaters

The MI band heater from Watlow® is a high-performance heater. The band heater's performance and name are derived from Watlow's exclusive mineral insulation—a material with much higher thermal conductivity than mica and hard ceramic insulators used in conventional heaters. A thin layer of the “high” thermally conductive MI material is used to electrically insulate the element wire from the inside diameter of the heater sheath. A thicker, “low” thermally conductive layer backs up the element wire directing the heat inward toward the part being heated. 

High thermal conductivity of MI and low mass construction provides rapid response to temperature control and avoids thermal lag.

Operating temperatures up to 1400°F (760°C) allows safe melting of resins such as PEEK™, Teflon®, Ultem® and Zytel®

Higher watt densities contribute to faster heat-up and throughput for increased productivity

Stainless steel cover and side fold design resists contamination from overflow of plastic or other free-flowing materials

Attached clamp bars eliminates cumbersome clamping straps, making installation easier

Applications and Technical Data 

General Limitations 

• Maximum width of 1 in. (25 mm) diameter heater is 11/2 in. wide (38 mm) 

• Maximum heater width: 2x heater diameter 

• Minimum I.D. for Type B, C, E and H leads: 1 in. (25 mm) 

• Minimum I.D. for Type B—90° leads: 11/8 in. (29 mm) 

• Maximum lead amperes: 12.5A per pair 

• SLE maximum: 17.0A 

• Maximum amperes (post terminals): 30A per pair 

• Minimum diameter and width for SLE: 4 in. x 11/2 in. (102 x 38 mm) width 

• 90° leads not available over 250VAC 

• Minimum I.D. for post terminals: 11/4 in. (32 mm) 

Gaps 

• ≤ 3 in. = 1/8 in. nominal 

• 3 in. ≤ 6 in. = 1/4 in. nominal ±1/8 in. 

• 6 in. ≤14 in. = 3/8 in. nominal ±1/8 in. 

• >14 in. = 1/2 in. nominal ±1/4 in. 

Use our Contact Form HERE to get a quote on Watlow Band /BarrelHeaters

MB1A1AN1

MB1A1AN2

MB1A1AN3

MB1A1AN4

MB1A1JN1

MB1A1JN2

MB1A1JN3

MB1A1JN4

MB1A1JN5

MB2A1JN1

MB1E1AN2

MB1E1AN3

MB1E1JN1

MB1E1JN2

MB1E1JN3

MB1J1AN1

MB1J1AN2

MB1J1AN3

MB1J1AN4

MB1J1AN5

MB1J1JN1

MB1J1JN2

MB1J1JN3

MB1J1JN4

MB1J1JP4

MB1J1JP6

MB1J2AN1

MB1J2AN2

MB1J2AN3

MB1J3AN1

MB1J3AN2

MB1J3AN3

MB1N1GX3A

MB1N1JN1

MB1N1JN2

MB1N1JN3

MB1N2AN1

MB2A1AN1

MB2A1AN2

MB2A1AN3

MB2A1AX6B

MB2A1JN1

MB2A1JN2

MB2A2AN1

MB2A2AN2

MB2A2AX2A

MB2E2AX7

MB2E2JN1

MB2J1AN1

MB2J1JN1

MB3A1AP1

MB3A1JP1

ME3A1JP10

MB3J2AP2

ME3L1JP5

MB4A1AP1

MB4A1JP2

ME4A1JP11

ME4A1JP12

MB4J2JP1

ME5A1JP8

ME5E1JP9

ME5E3AP5

ME5E4JP2

ME5E4JP3

ME5J1JP1

ME6A1JP2

ME6J1JP5

ME6N1JP6

ME6N1JP7

ME6N4AP2

ME6N5AP3

ME6N6AP5

ME7A1JP4

ME7J1JP4

ME7L3AP1

ME8A1JP4

ME9A1JP1

ME9J3AP2

ME11E3AP2

ME11E5AP1

Use our Contact Form HERE to get a quote on Watlow Band /Barrel Heaters

Sords Electric
216-765-4230
www.sordselectric.com

Band Heaters and Barrel Heaters from Watlow 

TriVolt Standard Band Heaters PWB Series

Sords Electric Sells TriVolt Band Heaters - Standard Power Bands

The Power Band Heater by Tri-Volt - 

Contact Sords Electric HERE

Purchase HERE

The TriVolt power band heaters can operate at sheath temperatures of up to 1300º F continuously depending on the diameter, width and application. The interior of the TriVolt Power Band heater are manufactured with ceramic tape, nichrome wire and high temperature cement.  The TriVolt Power Band heaters respond quickly to applications that require high temperatures and high watt densities (Watts per square inch). All the moisture is removed from the Power Band Heaters by their baking processor 850º F for 8 hours. Tri-Volt has included a small profile termination on the models PWB1 and PWB2 for those applications with restricted space.
All of the TriVolt Power Band Heaters are clamped down with an 18 gauge stainless steel strap to reassure there are no air gaps between the barrel and the heater which improves the band heaters conductive performance. Both the outer and inner shell are manufactured with 3042b stainless steel channel sheet metal providing a compressed process while forming the band heaters. The TriVolt Power Band Heaters are manufactured in a variety of electrical termination styles and can have holes for thermocouples or other reasons.

Applications: Plastic Extrusion, Injection Molding, Blow Molding, Pressure Molding, Structural Foam, packaging, Chemical, Oil and Gas

Specifications: Up to 1300º Sheath Temperture, 100 watts/sq. inch, 120 and 240 volts.

Construction: 1 or 2 piece, Expandable, partial Coverage, Stainless Steel, Minimum Diameter is 1.5 inches, minimum width is 1 inch.

Electrical Connections: Post Terminal, Fiber glass sleave, Metal SS braid, Armour Cable, Ground Post, Dual Voltage, Low Profile Cap, 3 phase, 120 or 240 volts

Terminal Housing: Terminal Box, Terminal Box with Ceramic Block, European Plug, European Plug with terminal box, Ceramic Post Covers, Brass Cap for Heater with different Angle Lead Exits

Clamping Methods: Independent or full strap, Spring-Loaded Barrel Nuts

Features: Low Profile band Heater, Connection Position is 180º from the gap, 18 Gauge 430 stainless strap for maximum clamping, Up to 1300º sheath Temperature

Tri-Volt PWB Band Heater, PWB-02-1A, 1 inch ID, 1 inch width 120 volts, 100 Watts

Tri-Volt PWB Band Heater, PWB-03-1C, 1 inch ID, 1 inch width 120 volts, 200 Watts

Tri-Volt PWB Band Heater, PWB-05-1B, 1 inch ID, 1.5 inch width 240 Volts, 300 Watts

Tri-Volt PWB Band Heater, PWB-43-1A, 2 inch ID, 2 inch width 240 Volts, 750 Watts

Purchase HERE

Sords Electric
216-765-4230
www.sordselectric.com

Watlow Firerod Cartridge Heaters in Stock

Sords Electric has the below heaters in stock from Watlow

Watlow Cartridge Heater G10A31-L12, 240 vac, 600 watts, (500w / 208 vac)

3/8 inch diameter and 10 inch length and 12 inch leads

Watlow Cartridge Heater G10A32-L12, 240 vac, 1000 watts, (830w / 208 vac) 

3/8 inch diameter and 10 inch length and 12 inch leads

216-765-4230

info@sordselectric.com

Q'Mark MUH Electric Unit Heaters

Sords Electric and Q'Mark keep you Warm with MUH Unit Heaters

Modular Unit Heaters from Q'Mark or MUH Heaters have been the industry standard for decades since their inception at Chromalox Comfort Conditioning. The Q'Mark MUH is the most specified and used unit heater for commercial applications. The MUH comes in KW sizes from 3 kw to 50 kw (10,230  to 170, 500 BTUs) and voyages from 208 - 600.

Common applications for the MUH are factories, warehouses, garages, stores, shipping rooms, power stations, aircraft hangers, convention halls and sports arenas.

Heaters are made from heavy gauge die-formed steel housing with the front and back case in t neutral grey color while the wrap around steel section is Statuary Bronze cooler as are the Stainless Steel louvers.

The heaters include an automatic reset linear thermal cutout for over heat protection and the automatic fan delay keeps blowing after the elements have turned off to distribute the heat.

Q'Mark MUH Heater

Q'Mark Heaters on Sords Electric

Sords Electric 
800-929-2845

Marley Q'Mark Garage Heater GH48R

Sords Electric Stocks the QMark GH48R Garage Heater
(Fahrenheat FLCH4R)

The Marley Q'Mark GH48R garage heater comes with a remote for easy temperature setting and programming.  The heater does have to be hard wired.

Specifications:
Voltage:     208/240
Wattage:  3600/4800
Amps:   17/20
CFM:  160
Warranty: 1 Year

Marley Q'Mark GH48R Garage Heater

The QMark Garage Heater GH48R comes with an IR remote and has a digital interface as well as an auto timer.  The timer can be set to turn off after a specified time so the heater will not potentially run all night if left alone or forgotten.  Timer is up to nine hours.

The Universal bracket can be mounted three different ways for wall or ceiling mounting or horizontal throw or an angled throw of the air.

Ceiling Mount

Wall Mount

Ceiling Mount 30 Degrees

Q'Mark GH48R Applications include:

Garages, Barns, Workshops, Storage Facilites, Basements, Boathouses, Pool Sheds, Cabanas

Factories, Warehouse, Stores, Stock Rooms, Storages Sheds (Buildings), Farm Shops

Unit weight is about 14 pounds.


Sords Electric
216-765-4230
www.sordselectric.com

Q'Mark Unit Heater MUH35C

Sords Electric Stocks the Q'Mark MUH35C Unit Heater from QMark

Wattage: 5000 or 3300 Watts @ 240 volts
         3700 or 2500 Watts @ 208 volts

Voltage: 208 or 240 Volts
Amps: 21.0, 14.0
      18.0, 12.0
(Depending on the voltage and the heat selector Switch.)

CFM: 210
Air Throw: 24 feet
Temperature Change: 71 Degrees F.

The Qmark MUH35C unit heaters is a universal unit heater that can be wall or ceiling mounted or can sit n a floor for quick spot heating. On board controls make this heater easy use and operate. The air flow can be directed or positioned for precise control. The Q'Mark MUH35 can be hard wired or has an optional cord for portability.  Note: This is a 240 volt heater and cannot be plugged into a standard 120 volt home receptacle.  The optional Cord is part number PHCS1B.

Features:
Multiple Wattage Selector Switch
Fan Only Switch
Built in Thermostat with 40-90 Degree Range
Integral Bracket for Wall or Ceiling mounting
Advanced Pull Through Air Flow
Manual Reset thermal Cutout for safety
UL, NEC and OSHA

Buy the Q'Mark MUH35C HERE.

Buy the QMark MUH35C with Cord HERE.



Sords Electric
216-765-4230
www.sordselectric.com

Q'Mark CWH1151DSAF Architectural Small Wall Heater

Sords Electric Stocks The QMark CWH1151DSAF Wall Heater

KW: 1.5     /  Volts: 120 AC 
BTU: 5120  /  Amps: 12.5

The Q Mark CWH series Wall Heaer is great for smaller spaces like bathrooms, hall ways, dens, small offices, vestibules, breezeways, workshops, work out rooms and small garages.
(See our Garage Heater GH48R for larger garages and ceiling mount).
The Q'Mark CWH1151DSAF has a fast heat response with a compact design and puts out 5102 BTUS or 1500 watts. The bar-stock grill in bronze is designed for optimal airflow.
The heater series can come n vantages of 120. 208, 240 or 277 and wattages up to 2000.

Included with the the Qmark  CWH 1151DSAF :

Integral Thermostat: 40-85 F

Fan Delay Switch which delays the fan coming on until there is warm air to discharge.

Manual Reset Thermal overload protector for protecting against an inadvertent over heating situation, like an air flow blockage.

1 year workmanship warranty and 5 years on the element.

Do Not install closer than 4 inches to the floor.
Do Not install behind a towel rack, draperies, behind a door, in a closet or other obstructed space.

The heater size is 10-5/8 x 12-1/8 x 4 Inches

Click HERE to order.

Click HERE to contact Sords Electric.

216-765-4230
info@sordselectric.com

COS-E Wall Heater from Q'Mark

Q'Mark COS-E CZ1512T WALL Heater in Stock at Sords Electric

1. COS-E Series - Residential Fan-Forced Zonal Wall Heaters

QMark COS-E CZ1512T

Marley Q'Mark CZ1512T

Volts  120

Watts  1500

CFM  65 cfm

Amps  12.5

Weight  10 pounds

Listing  cETLus

Applications include Bathrooms, Basements, Remodels, Bedrooms, Hallways.

Easy to install with included back box.

• Safety listed by Intertek (ETL) for use in the USA and Canada complying with ANSI/UL2021 and CSA 22.2, NO. 46 Safety Standards
  
• Dual protection: self-hold limit with one time thermal fuse
  
• Efficient quiet operation from smooth running multi-layer impeller 
  

• Adaptable for retrofits into 7 7/8” x 11 1/2” x 4” back box (such as provided with UL-approved Cos-E and Cadet CS Models) rough- in opening same if new box is desired 
  

CLIP-N-FIT® - Patented feature (US Patented No. 6,172,343) allows the installer to change the wattage of the heater to a lower output without moving jumper wire. Each heater is factory wired for its maximum wattage. To reduce to half wattage, clip jumper wire on heating element. This patented feature also prevents the operator from changing wattage after installation to a higher wattage. 

Click HERE to purchase.

800-929-2845

www.sordselectric.com

Q'Mark Residential Infrared/Radiant Heater QHRA11115W.

Sords Electric Stocks the Qmark HRA11115W 
Radiant Heater


The Q'Mark Infrared QHRA11115W heater is ideal for residential and light Commercial spot heating in Basements, Patio, Terraces, Verandas, Gazebos, Door Steps, Changing Rooms, Health Spas, Hotels, pubs and Outdoor Bars. The heater is wall mounted at least 7 feet above the floor. The Heater's specifications are 1500 watts, 120 volts, 5115 BTU, and standard 120 volt plug. Heater is cUL and ETL listed.

Q Mark Radiant Heater HRA Style

UPC 685360163710
Volts  120
Phase  1
Amps  12.5
Watts  1500
BTU   5115
Dimensions  17-15/16" x 3-1/2" x 5-1/8"  (LxWxH)


Notes:
Q'Mark Heater to be WALL mounted ONLY with included wall mount bracket.  Do NOT mount heater to a ceiling.
QMark HRA Heater MUST be mounted at least 8'3" above the floor.
The top of Q Mark QHRA heater MUST be at least 12 inches from the ceiling and have 36 inch space on each side from any walls.
(The heater gets hot).

Click HERE to purchase.

Other Radiant heaters from Q'Mark:

QHRA66420B  240 volts, 2000 watts, 6824 BTU
QVRC4420SG  240 VOLTS, 2000 WATTS, 6824 BTU
QVRC4440DTG  240 VOLTS, 4000 WATTS, 13648 BTU
QVRC4440DWG  240 VOLTS, 4000 WATTS, 13648 BTU

Call for information.
www.sordselectric.com
800-929-2845

Sords Electric Stock Q'Mark heaters

Q'Mark Electric Heaters in Stock

Click Here to View and Buy

1500 watts and Q'Mark QHR11115W Radiant Heater
120 volts with cord and plug with White Grill

Q'Mark CZ1512T Wall Heater 

1500 watt, 120 volts

Q'Mark CWH1151DSAF Architectural Wall Heater 

120 volt 1500 watts with Grey Grill

Q'Mark CWH3150F Commercial Grade Wall Heater

120 volts and 1500 watts with White grill

Q'Mark MUH35 Portable Unit Heater 

5000 watt 240 volt heater with combo ceiling bracket or floor stand

Q'Mark MUH35 with Cord and plug.  BUY HERE.

Q'Mark GH48R Garage Heater  

4800 watt, 240 volt Blower Heater, Black

HT1502SS Smart Wall Heater with Grey Grill  
1500 watt programmable 120 volt heater.

HT1502SSNW Smart Wall Heater With White Grill  
1500 watt programmable 120 volt heater.

www.sordselectric.com

216-765-4230

Watlow 375 Strip Heaters

Sords Electric Supplies Watlow Strip Heaters

Our New Webstore opened in April 2020!!

Watlow 375 Strip heaters are named for their .375 inch thickness and is capable of high temperatures and high watt densities.  The strip heater come in offset, parallel and split  (end-end) terminals.  The offset configuration is the most common know as OT. The coiled nickel-chromium wires are placed in the center of the heater and then imbedded with magnesium oxide (Mg)) insulation and compacted into a solid mass to hold the element in place and provide electrical insulation. MgO is an excellent heat conductor with high dielectric strength.  The outer sheath is aluminized steel or Stainless Steel.

Sheath temperatures to 1100 and 1200.  Watt densities to 100 watts per square inch.
UL approved to 240VAC and CSA approved to 600VAC.

To view the Watlow Catalog Sheet click HERE!




Watlow strip heater Aluminized Steel sheath SGA1J47RO1
48 inch, 240 volt, 2250 watt

Watlow Strip Heater Aluminized Steel sheath SGA1J38JO3
36 inch, 240 volt, 1500 watt

Watlow Strip Heater Aluminized Steel sheath SGA1J35RO1
36 inch, 240 volt, 1000 watt

Watlow Strip Heater Aluminized Steel sheath SGA1J33JO1
33 inch, 240 volt, 750 watt

Watlow Strip Heater Aluminized Steel sheath SGA1J26NO2
27 inch, 240 volt, 1000 watt

Watlow Strip Heater Aluminized Steel sheath SGA1J19JO1
19 inch, 240 volt, 1000 watt

Watlow Strip Heater Aluminized Steel sheath SGA1J15EO4
15 inch, 240 volt, 500 watt

120 volt strip heaters available too.
Go to our complete list of Watlow Strip Heaters, HERE.

Contact us HERE or as below.
www.sordselectric.com
888-929-2845

Watlow FireRod Cartridge Heaters

Watlow Firerod Cartridge Heaters from Sords Electric

The Watlow FIREROD® cartridge heater revolutionized the heating element industry in 1954 when it was patented as the first swaged cartridge heater. The mechanical procedure of swaging reduces the diameter of the heater by compacting the unit; this directly improves the heat transfer and efficiency of the heater.

Watlow FIRE ROD cartridge heaters are built using only the finest materials and construction methods and are backed with extensive quality assurance programs. With premium materials and tight manufacturing controls, the FIREROD heater provides superior heat transfer, uniform temperatures, resistance to oxidation and corrosion and a long life even at high temperatures.

Alloy 800  Sheath FireRod Cartrdige heaters have a max operating temperature of 1400 F (760C) and a maximum watt density of 400 W/in². Watlow Fire Rod Cartrdige heaters come in 120, 240 and 480 voltages.  Wattages from 25 to 4700 watts.

Applications:

• Semiconductor chamber heating
• Semiconductor wafer lead connection
• Semiconductor wire and die bonding
• Freeze protection and deicing of equipment in cold climates or applications
• Humidity control
• Patient comfort heating used in medical devices
• Mold die and platen heating
• Seal bars used in packaging equipment
• Test sample heating in gas chromatography

Camber

Camber is defined as the maximum deviation of the heater’s centerline from straight. FIREROD camber within allowable tolerances is verified via passage through a cylindrical gauge of specified length and diameter. Normally, slight camber does not present a problem since the heater will flex enough to fit into a straight, close-fit hole.

Component Recognition File Numbers

•  UL® component rated to 240VAC (file number E52951)

•  CSA component rated to 240VAC (file number LR7392) 

•  VDE component rated to 240VAC (file number 10062-4911-0006)

Note: Not all options or combinations of options are covered. UL®, CSA, VDE and CE marking is available upon request.

Watlow FIREROD® catalog page for all sizes:  CLICK HERE!

An assortment of  Watlow Fire Rod Cartridge heaters.

Watlow Firerod Cartridge Heater, 120 volts, 25 Watts, 1/8 diameter, C1E14

Watlow Firerod Cartridge Heater, 120 volts, 50 Watts, 1/8 diameter, C1E13

Watlow Firerod Cartridge Heater, 240 volts, 35 Watts, 1/8 diameter, C1E42

Watlow Firerod Cartridge Heater, 120 volts, 30 Watts, 1/8 diameter, C1J5

Watlow Firerod Cartridge Heater, 120 volts, 60 Watts, 1/8 diameter, C1J6

Watlow Hot Runner Cartridge Heater, 240 volts, 200 Watts, 1/4 diameter, E1JX442A

Watlow Hot Runner Cartridge Heater, 240 volts, 200 Watts, 1/4 diameter, E2AX619A

Watlow Hot Runner Cartridge Heater, 120 volts, 200 Watts, 1/4 diameter, E2JX287A

Watlow Hot Runner Cartridge Heater, 240 volts, 200 Watts, 1/4 diameter, E3AX575A

Watlow Firerod Cartridge Heater, 120 volts, 100 Watts, 1/4 diameter, E1A52

Watlow Firerod Cartridge Heater, 240 volts, 100 Watts, 1/4 diameter, E1A66

Watlow Firerod Cartridge Heater, 120 volts, 200 Watts, 1/4 diameter, E1J42

Watlow Firerod Cartridge Heater, 120 volts, 250 Watts, 1/4 diameter, E2A72

Watlow Firerod Cartridge Heater, 240 volts, 300 Watts, 1/4 diameter, E2A83

Watlow Firerod Cartridge Heater, 120 volts, 250 Watts, 3/8 diameter, G3A52

Watlow Firerod Cartridge Heater, 240 volts, 250 Watts, 3/8 diameter, G3A54

Watlow Firerod Cartridge Heater, 120 volts, 500 Watts, 3/8 diameter, G3A119

Watlow Firerod Cartridge Heater, 240 volts, 500 Watts, 3/8 diameter, G3A120

Watlow Hot Runner Cartridge Heater, 240 volts, 625 Watts, 1/2 diameter, J5AX178B

Watlow Hot Runner Cartridge Heater, 240 volts, 850 Watts, 1/2 diameter, J6JX45C

Watlow Firerod Cartridge Heater, 120 volts, 125 Watts, 1/2 diameter, J1A31

Watlow Firerod Cartridge Heater, 240 volts, 200 Watts, 1/2 diameter, J1E52

Watlow Firerod Cartridge Heater, 120 volts, 200 Watts, 1/2 diameter, J1J59

Watlow Firerod Cartridge Heater, 120 volts, 400 Watts, 1/2 diameter, J2A81

Watlow Firerod Cartridge Heater, 240 volts, 400 Watts, 1/2 diameter, J2A82

Watlow Firerod Cartridge Heater, 120 volts, 500 Watts, 1/2 diameter, J3A110

Watlow Firerod Cartridge Heater, 240 volts, 500 Watts, 1/2 diameter, J3A111

Watlow Firerod Cartridge Heater, 120 volts, 1000 Watts, 1/2 diameter, J3A79

Watlow Firerod Cartridge Heater, 240 volts, 1000 Watts, 1/2 diameter, J4A73

Watlow Firerod Cartridge Heater, 120 volts, 200 Watts, 5/8 diameter, L1E24

Watlow Firerod Cartridge Heater, 120 volts, 250 Watts, 5/8 diameter, L1E27

Watlow Firerod Cartridge Heater, 240 volts, 250 Watts, 5/8 diameter, L1J24

Watlow Firerod Cartridge Heater, 240 volts, 500 Watts, 5/8 diameter, L3A113

Watlow Firerod Cartridge Heater, 240 volts, 750 Watts, 5/8 diameter, L3A71

Watlow Firerod Cartridge Heater, 240 volts, 1000 Watts, 5/8 diameter, L4A71

Watlow Firerod Cartridge Heater, 120 volts, 800 Watts, 5/8 diameter, L5G3

Watlow Firerod Cartridge Heater, 240 volts, 800 Watts, 5/8 diameter, L5G1

Watlow Firerod Cartridge Heater, 240 volts, 500 Watts, 3/4 diameter, N3A12

Watlow Firerod Cartridge Heater, 240 volts, 1000 Watts, 3/4 diameter, N4A15

Watlow Firerod Cartridge Heater, 240 volts, 2000 Watts, 3/4 diameter, N6A22

Watlow Firerod Cartridge Heater, 240 volts, 4000 Watts, 3/4 diameter, N12A25

Watlow Firerod Cartridge Heater, 240 volts, 4500 Watts, 3/4 diameter, N14A21

Watlow Firerod Cartridge Heater, 240 volts, 5000 Watts, 3/4 diameter, N18A15

Watlow Firerod Cartridge Heater, 240 volts, 5500 Watts, 3/4 diameter, N24A13

Buy Watlow Firerod Heaters HERE!

To order via Phone, please call 800-929-2845

www.sordselectric.com